Agile

View Original

What is unconventional?

Subsurface science in the oil industry has gradually shifted in emphasis over the last five, maybe ten, years. In 2000, much of the work being done in our field was focused on conventional oil and gas plays. Today, it seems like most of what we do has something to do with unconventional resources. And this is set to continue. According to the American Petroleum Institute, unconventional gas production accounts for almost 50% of today's US Lower 48 production total of about 65 billion cubic feet per day, and is expected to reach 64% by 2020. In Canada, where unconventional gas is also very important, unconventional oil is at least as significant to geoscientists, especially bitumen. According to the Alberta govermnent, production from the Athabasca oil sands in 2011 will be about 2 million barrels per day.

To many people, 'unconventional' means 'shale', but that definition is too narrow. The important Montney Formation (shown) is a tight sand or silt, and probably not entirely self-sourced.But what does 'unconventional' mean? The short answer is "not conventional", which is more helpful than it sounds, and the long answer is "it depends who you ask". This is because where you draw the line between conventional and unconventional depends on what you care most about. To illustrate the point, here are some points of view:

Economist   With today's technology, unconventional resources cannot be profitably produced with conventional development and production methods. This relative view seems circular, but 'conventional' here essentially means 'off the shelf'. This definition reflects the fact that many unconventional resources, like the oil sands or tight gas, were bypassed for decades because they were uneconomic at the time. It could be argued that, by this definition, shale gas is no longer unconventional in Texas, and bitumen is no longer unconventional in Alberta. Other resources, like methane clathrates for example, will be unconventional for the foreseeable future. One weakness of this definition, in my opinion, is that it admits resources like those in the offshore of the Beaufort Sea, which are surely uneconomic today, but are not what most people would call unconventional

Reservoir engineer   Unconventional resources cannot be produced with a vertical and/or an unstimulated well. In other words, a horizontal well and/or some sort of intervention to increase hydrocarbon mobility is required. Mobility depends on the permeability of the rock and the viscosity of the hydrocarbon. By this definition, shale gas and bitumen will always be unconventional. 

Petrophysicist   Below some critical permeability, it is no longer possible to measure permeability accurately with conventional methods. The US government calls a reservoir with less than 0.1 mD permeability 'tight'. The micropermeameter, for measuring the permeability of core, does not read below 0.01 mD. I have heard petrophysicists think of both 1 mD and 0.01 mD as a cut-off, below which the rock is 'unconventional'. 

Geologists examining an outcrop of Early Triassic Montney Formation fractured turbidites at Cold Sulphur Springs, near Jasper, Alberta, Canada.Geologist   One or more elements of the classic model of a petroleum system (source, migration, reservoir, trap, seal, and timing) are missing from an unconventional system. For example, shale gas is produced from a source rock, with no need for a reservoir, trap, or seal. Bitumen is a solid, so the presence of a trap or seal today is not required (though it was required to allow the oil to accumulate in the first place). This definition will doubtless seem increasingly dated; even today I'm not sure that the concept of a petroleum system is still a useful one, except in a handful of circumstances. 

Hydrogeologist   Hydrocarbons are not floating on a (mostly) down-dip water leg in an unconventional reservoir. 'Mostly' because conventional reservoirs can have a tilted hydrocarbon-water contact in some circumstances. Many unconventional systems are quite counterintuitive with respect to their hydrodynamics: tight gas reservoirs often have a regional aquifer updip of the gas. In the Cretaceous McMurray Formation, the reservoir for much of the Athabasca oil sands, there is often water above and below the reservoir, and possibly also within it. 

All of this made me wonder: is there a geophysical approach to defining unconventional? It got me thinking about what sorts of approaches we adopt with unconventionals. In oil sands we are concerned with high resolution seismic, density inversion, lithology prediction, perhaps even viscosity prediction. We do a lot of time lapse monitoring. In shale gas it's all about natural fracture prediction and frac stimulation monitoring. I think you have to get down to rock physics to find a common thread, so here is my proposal:

Geophysicist   Gassmann's equations, which predict that the fluid in a rock does not change its shear modulus (only its bulk modulus), do not hold in an unconventional reservoir. I think this is because, in unconventional reservoirs, the hydrocarbons are intrinsically bound to the rock in some way, and thus can't be easily separated. Bitumen is solid, supporting shear waves, and forms a matrix around the rock grains; shale gas is adsorbed onto the clays and kerogen grains in the rock, making it similarly indivisible. 

Maybe there are still other ways to define unconventional. Reservoir flow simulation methods, for example, must use specialized models (or a lot of fudge factors!) to succeed in unconventional reservoirs.